HVACNews.com

	Power Tools

Bosch TS1007 Dado Insert

Zoom

Bosch TS1007 Dado Insert

(30 customer reviews)

SKU:

TS1007

In Stock

Availability: Usually ships in 1 business days

Bosch TS1007 Dado Insert for 10" Table Saw Bosch Power Tools and Accessories is one of the divisions within the Robert Bosch Tool Corporation, which is one of the largest power tool and accessory manufacturers in the world. Bosch provides a complete line of corded and cordless power tools and accessories engineered to survive any jobsite and allow professionals to take control of their work. Bosch TS1007 Dado Insert for 10" Table Saw Features: Table Saw Dado Cutter Insert. Model TS1007. For use with stack dado/rabbet cutters. Table Saw Attachments Part No. TS1007 Used on Model No. 4000 Sales Pack Quantity 1

List Price:	$17.29
Our Price:	$12.04 & eligible for FREE Super Saver Shipping on orders over $25.
You Save:	$5.25 (30%)

Note: Item may be sold and shipped by another company. Learn more.

Product Details

Product Length:	0.0 inches
Product Width:	0.0 inches
Product Height:	0.0 inches
Package Length:	13.7 inches
Package Width:	3.8 inches
Package Height:	0.7 inches
Package Weight:	0.35 pounds
Average Customer Rating:	based on 30 reviews

Features

Dado insert for use with stack dado and rabbet cutters
Accommodates up to 3/4-inch lumber
Plastic construction
Includes 1 insert; blade and saw not included
3-13/16-inches; 1-year warranty

Customer Reviews

Average Customer Review: 3.5

( 30 customer reviews )
Write an online review and share your thoughts with other customers.

Most Helpful Customer Reviews

82 of 83 found the following review helpful:

Info on how to use dado Insert Aug 23, 2006 By Geo "Geo"
Dado insert was functional. It fit properly. To use a 13/16" dado stack with this insert on your saw you need to do this. (Per Bosch Tool customer service)

Thank you for writing Bosch Power Tools. When mounting dado blades on
the Bosch 4000 table saw, follow this procedure which was omitted from
the owners manual. This saw will handle up to a 13/16" wide dado blade.
Remove both blade washers from the arbor shaft. Install & use the Outer
washer as the Inner washer, than[sic] mount your dado blade set, than[sic]
install the lock nut. An outer washer is not needed for a dado set. This
procedure will provide proper spacing of your dado blade set. Changing
blades can be a bit tight, but if you insure the blade is elevated to it's
maximum height you shouldn't have any problem. The reason for this is
because the dust containment shroud is rather close to the blade to
contain saw dust from blowing all over the place. If you have any further
questions, please write back.

24 of 24 found the following review helpful:

Better instructions should be written for this insert. Nov 08, 2007 By W. Joel Porter "handyman carpenter"
I've had my Bosch table saw for a little over 3 years and use it every week in my carpentry business. It has yet to disappoint me. Up until now I had not purchased the dado insert because of some of the poor reviews. I had made my own insert and have put up with the struggle of using it all this time (I had to screw it in each time and place washers underneath to make it flush). After my last frustrating effort with my homemade insert, I decided that at $13, Bosch's dado insert couldn't be any more frustrating than using my own homemade one. Boy had I been wrong (and the reviewers that I had listened to). It took almost nothing to snap it in and adjust it to level. Those are the ONLY instructions that come with it - in three languages. Woohoo! The hitch came when I needed to cut a wide dado. This is where the additional instructions would have been helpful (and would have kept some of the reviewers from giving it low marks). On a wider stack you will need to remove the inner arbor washer and replace it with the outer washer, then put on your stack of blades. I would rate this 5 stars if they would only give you this small, but important, bit of info with the package. Even the instruction book that comes with the saw when it mentions working with dado or molding heads doesn't tell you this. All it says is, "Instructions for operating the Dado and Molding Heads are contained in the booklet furnished with these accessories. ALWAYS USE APPROPRIATE TABLE INSERT LISTED UNDER ACCESSORIES." Hmmmm, neither set of instructions tells you anything about swapping out the arbor washers. Fortunately I was able to figure this on my own. I wish now I had been using this from the get go and had not been influenced by negative reviews for so long.

71 of 81 found the following review helpful:

Dado insert Apr 09, 2002 By Steven Fischer
Disappointed with the insert. Love the saw and the stand. The dado insert only allows a 1/2" cut. A 3/4" dado setup rubs against the insert. You'd need to take the stabilizer off to have the blades be centered. It's as if no one tried it after it was developed.

23 of 25 found the following review helpful:

Second one works fine Feb 08, 2004 By Russel Miranda "russthegeek"
Well, the first one I received was bent -- laying it face down on the table top, it would rock considerably. If adjusted so the front and back edge were in line with the table, it was high in the center. I figured that would probably throw my cuts off, so I just shipped it back. Amazon had a flat replacement at my door a few hours after I managed to drop the old one in the mail. The replacement works great, and I'd probably rate it 4 stars if the first one hadn't been bent. Also, considering that the manual for the saw itself says very little about mounting a dado stack, it might be nice if the insert gave you some more info. I had to email Bosch tech support to get the secret for getting beyond 1/2".

13 of 13 found the following review helpful:

Dado Insert, a must have. Mar 08, 2007 By Bradley T. Riggleman
This one little accessory is a must have for your Bosch 4000 table saw. It fits the table top securely and once installed allows Dado cuts up to 3/4".

The one thing you need to know in order to get the max. width cut when mounting your dado blades, you must use the outside washer on the inside. Then use the standard 23mm lock down nut on the outside without a washer, or in my case, I used one of the dado shims as a washer.

Just get this, it works.

See all 30 customer reviews on Amazon.com